Frigidaire 5303935066 Burner Igniter for Oven Burners, Gold

Great inexpensive part
Way cheaper then the $100 mfr part

Fixed broiler igniteron Fridigaire Gallery gas range/oven
This product is a suitable replacement for the OEM igniter on my Frigidaire Gallery Range/Oven. This is an easy enough install, but it should be known this install is not a direct replacement. The igniter shipped requires one to cut and wire nut the two wire together. A wire snips and a socket/wrench are needed to remove all the nuts holding the parts together.The entire repair took about 30 minutes, the entire range/oven must be removed from the wall to get at the back cover, where the wiring is spliced to the control board.The kit comes with the ceramic wire nuts needed to complete the repair.If you have a small amount of wiring knowledge and are not afraid of a few wrenches, you can do this repair.

Made by Roberstshaw in the USA. Tag says Robertshaw igniter model 41-205
I have a 20 year old Viking VGIC305 30 inch freestanding stainless steel range. I got good service from the original oven igniters but they are finally dying 20 years later. There are three igniters total in my 30 inch Viking range – 2 for the oven, one for the broiler. Your experience with the number of igniters may vary.I found dozens of igniters across the online spectrum from the Viking OEM model (~$165 EACH!!) to some suspicious Asian knockoffs for about $12 each. I was not spending almost $500 on three OEM Viking igniters for a 20 year old range. The truth about where the products are sourced is sketchy at best.This particular igniter on Amazon is listed as being made by Frigidaire and is a good example of the online confusion for country of origin and manufacturer. The ones I received from Amazon are actually made by Robertshaw for Frigidaire and probably a lot of other stove companies. Robertshaw is a 120+ year old American company based in Illinois that makes electrical parts, controls and valves to name a few. See my attached photos for the Robertshaw/Made in USA tag. The Robertshaw model is the one with the shorter ceramic body.The Robertshaw igniters I received from Amazon are identical to the ones in my Viking range minus the 2 spade clips on the wires. For $145 less (each) than the Viking OEM igniters, I added an insulated spade connector myself and connected it with ceramic wire nuts. Don’t use regular wire nuts, they won’t take the oven heat, could melt a cause a short and/or a fire. No bueno!The major difference between the OEM Viking, this Robertshaw model I bought and the Asian knockoffs I saw appearance wise is that the metal igniter element on the Viking and the Robertshaw is a flat rectangle. On the Asian knockoffs, it’s circular. I don’t know what difference that makes for the usability or longevity of the Asian models but I’d rather not find out.I bought three of these Robertshaw igniters and I’ll likely buy 3 more shortly down the road once I see how these new ones perform for a few months. (I bought 3 more at a later date).OEM Viking parts are like BMW parts – absurdly expensive – and the supply chain changes constantly. If Ireorder these same igniters in a year, they might be sourced from overseas or elsewhere or simply vanish from Amazon.The photo on the right hand side shows the old igniter with the longer ceramic body. The Robertshaw model from Amazon is on the left.I got the new ones installed and they work great. Oven heats to 300 degrees in about 12 minutes, more than twice as fast as the old igniters. Hope this data helps!

Easy to install and will use this product again in the future.

This was a direct replacement for my white-westinghouse gas oven. Wired in very easy to the existing leads. Been a month so far no issues. Oven fires up within 10 seconds

This was to replace a defective hot surface igniter for a Blue Star 36” range.Early symptoms of pending failure included a very long time for stove to heat up (should normally take about 15 minutes to reach 350 C for a stove this size), faint gas smell sometimes, and eventually total fail with no heat at all, even though you may still see the igniter glow orange. If the temperature never reaches a preset limit, the gas valve doesn’t open, indicating that the igniter has now failed.There is an excellent video online that shows how to replace the igniter on this very particular Blue Star model, which actually shows the replacement part being exactly the same as the one sold here.I thought that the hardest part was actually to reinstall the oven door…a bit tricky.The only visual difference between the OEM part and this one is the ceramic portion extending a few inches behind the metal bracket which is not present on this replacement part…not sure why, but it works nonetheless as the bracket, ignitor, wires, all appear to be exact,…same as the required amps, 3.2 to 3.6 amps…and the price of course being much more attractive.Speaking of price, when I ordered this model mid November 2019, it was listed here at $35.65. A week later it’s now listed at $41. Not the first time I see prices vary so wildly on many different products on Amazon! Weird.Still, the OEM part is hard to find and if you do find it somewhere else, it’s often double or more.This is a Frigidaire/Electrolux part, so let’s hope it lasts.But for now, a first test after installing was a success, it lit up well within the 90 seconds required and I could hear a nice gas flow the way it’s supposed to be…total time to reach 350 C was 14 minutes…which is just below average on stoves that big.